Adam El Hajj

Windsor, Ontario  ·  University of Windsor

Adam El Hajj

Let's talk about Summer 2027.

I'm a UWindsor Electrical and Computer Engineering student (Honours Co-op, Class of 2029) based in Windsor, Ontario. I already work as an embedded systems engineer at MobiBot Technologies and a research assistant at the University of Windsor, and I co-founded the Lancer Autonomous Robotics Club. I'm looking for Summer 2027 co-ops in the Windsor area in electrical, controls, test, embedded systems, or robotics. If you have an opportunity in that space, I want to hear about it.

Key results

<10 mmWheelchair localization in Gazebo sim, vs. ground truth
100%ROS 2 test pass rate at MobiBot
±5 cm @ 3 mTurbo Avenger ranging, measured. $328 BOM
0DRC violations on the MIC5317 board in Altium

Where I fit

Electrical, controls & test roles

Robotics & embedded

ROS 2 nodes, Arduino + ESP32 builds, SPI / I2C / UART, Kalman filtering.

Power & PCB

Buck and LDO work in LTspice. Altium layout, 0 DRC, Gerbers out.

Test & telemetry

pytest, Docker, CI. Pub/Sub dashboards. Oscilloscope on the bench.

Work

Projects

Photos, plots and test output included. Sim results are marked as sim.

Autonomous Wheelchair Platform

Day-to-day work at MobiBot and AIRC. The chair maps a room, localizes, and avoids obstacles. Under NDA, so I can only post these two images and the sim clip. Sim localization is under 10 mm. Test suite sits at 100%.

Autonomous wheelchair platform: the electric wheelchair in the lab
The platform in the lab.
RViz maps from the autonomous wheelchair platform
RViz maps from simulation runs.
2D LiDAR picking up obstacles in Gazebo. Sim only.
Localization (sim)<10 mm
Test pass rate100%

Stack: ROS 2 · Gazebo / Isaac Sim · RViz · LiDAR

Code is private (NDA). Updates on LinkedIn ↗

Turbo Avenger: Ranging System

First-year Cornerstone project, team of five. Launcher had to hit a 30 x 40 cm target at 3 m, three times, with nobody touching it. I did the ranging. It landed within ±5 cm. Elastic-band arm, servo re-arm, dual-servo autoloader. $328 all in.

CAD model of the Turbo Avenger mechatronic system
CAD model of the system.
The Turbo Avenger team at the Cornerstone Design showcase
Team at the showcase: David Okunlola, Arian Navabpour, Lukas Waller, Zion Odibeli, and me.
Wiring map for the Turbo Avenger showing labeled connections from the 9 V battery pack to the Arduino and ESP32 boards
Wiring map. 9 V pack to Arduino and ESP32.
Isometric drawing of the Turbo Avenger with every part labeled, including the vertical feed tube and throwing spoon
Isometric drawing, parts labeled.
Orthographic drawing of the Turbo Avenger showing front, top, and side views with dimensions
Front, top and side views.
Turbo Avenger showcase poster covering the problem, design, cost, and results
Showcase poster.
Accuracy at 3 m±5 cm
BOM$328
Deliveries3 / 3

Stack: Arduino + ESP32 · Kalman filter

Code on GitHub ↗

Buck Converter: 100 kHz

12 V to 5 V buck in LTspice. Sized L and C, ran the transients. 4.86 V out, 3.78 mV ripple, current stays in CCM. Sim only, not built yet.

LTspice schematic of the 12 V to 5 V buck converter
LTspice schematic, 12 V to 5 V.
LTspice output ripple waveform for the buck converter with cursors showing 3.78 mV peak-to-peak
Ripple, cursors on: 3.78 mV pk-pk.
LTspice startup transient of the buck converter output settling at 4.86 V
Startup, settles at 4.86 V.
LTspice inductor current waveform of the buck converter rippling between 0.65 and 0.95 A
Inductor current, 0.65 to 0.95 A.
LTspice combined view of buck converter inductor current and output voltage, time-aligned
Current and voltage, same time axis.
LTspice duty cycle check showing 41.7 percent duty on a 12 V input gives 5.0 V output
Duty check: 41.7% on 12 V in, 5.0 V out.
Efficiency (sim)94.15%
Ripple (sim)3.78 mV pk-pk
L / C100 µH / 100 µF

Stack: LTspice

Code on GitHub ↗

LDO Regulator Board

5 V to 3.3 V board in Altium, MIC5317. Caps tight to the pins, solid ground on the bottom. 0 DRC, Gerber X2 out. Not fabricated yet.

Altium 3D view of the MIC5317 LDO regulator PCB
3D view in Altium.
Top view of the MIC5317 LDO regulator PCB showing connectors, capacitors and the regulator chip
Top layer.
DRC violations0
Output3.3 V
Rated current150 mA
Dropout155 mV

Stack: Altium · MIC5317 · 2-layer

Code on GitHub ↗

GridPulse: EV Charger Telemetry

Python pipeline for an EV charger. Voltage, current, power and temp go to a dashboard over Pub/Sub. Out-of-range reading trips the relay. Second shot is an actual trip: 72.9 °C on a 65 °C limit.

GridPulse EV charger telemetry dashboard
Dashboard, normal run.
GridPulse dashboard showing a critical fault with relay tripped on over-temperature at 72.9 degrees Celsius
Relay tripped on over-temp.

Stack: Google Cloud Pub/Sub · Python

Code on GitHub ↗

EV Telemetry Monitor

Python, SQLite, Docker. CI runs on GitHub Actions. 27 tests, 94% coverage, all passing. Screenshot is the run.

EV Telemetry Monitor pytest suite, 27 tests passing at 94% coverage
pytest output.
Tests27 passing
Coverage94%

Stack: Python · pytest · SQLite · Docker

Code on GitHub ↗

AEAC 2027

Leading LARC's entry. I set up a 50+ task board on GitHub so members can grab work and actually build. Phase 1 report due Jan 15, 2027.

In the lab

Oscilloscope and soldering, most weeks. Some PLC exposure.

Experience

Where I've worked

Sep 2026 — Present
Contract, part-time

Robotics & Embedded Systems Engineer, MobiBot Technologies

ROS 2 nodes for the wheelchair. Test pass rate: 100%.

May 2026 — Present

Research Assistant, Embedded Systems, AIRC, University of Windsor

Same wheelchair work, lab side.

Apr 2026 — Present
Co-Founder

Co-Founder & VP / Lead Robotics Systems Engineer, Lancer Autonomous Robotics Club

Started the club, now 80+ members. Got us Capstone Station 16, wrote the sponsorship package, started AEAC. I run the task board.

Oct 2025 — Present

Electrical Hardware Designer, UWindsor Rover Team

Electrical work for the competition rover.

Jun 2026 — Present

Internal Commissioner, Windsor Engineering Students' Society (WESS)

Event logistics.

Sep 2025 — Apr 2026

Outstanding Scholars Candidate (Top 100), University of Windsor

Top 100 incoming cohort. Student Vice-Chancellor, Jan to Apr 2026.

Skills

Toolbox

Embedded & Robotics

  • ROS 2, Gazebo, Isaac Sim, RViz, Nav2
  • Arduino, ESP32
  • SPI / I2C / UART
  • Kalman filtering
  • CAN on a virtual bus (python-can, sim)

Hardware & Power

  • Altium, KiCad
  • LTspice
  • Oscilloscope, soldering
  • PLC exposure

Software & Tools

  • Python, C/C++
  • pytest, Docker, GitHub Actions
  • MATLAB
  • Google Cloud Pub/Sub
  • Certs: Altium PCB Course, WHMIS 2015, ML + MATLAB Onramps